當前位置：在使用全自動封膠機時要注意哪些事項？
時間：2022-02-24 來源：http://yfcha.com/ 發布人：昌盛機械
在使用封膠機時要注意哪些事項：
What should be paid attention to when using the sealing machine:
1.混合膠在膠槍內滯留時間一定要控制在3-5分鐘內，否則蜂鳴器報警。
1. The retention time of mixed glue in the glue gun must be controlled within 3-5 minutes, otherwise the buzzer will give an alarm.
2.封膠之前要檢查雙組份膠的混合化，將膠擠到100mm的正方形，厚3mm的浮法玻璃上，再那一塊同樣的浮法玻璃在玻璃上一壓，在光亮處檢查，如混合膠內有白絲或黑絲，即混合不均勻。
2. Before sealing the glue, check the mixing of the two-component glue, squeeze the glue onto the 100mm square and 3mm thick float glass, press the same float glass on the glass, and check at the bright place. If there are white or black wires in the mixed glue, the mixing is uneven.
3.要時刻注意液壓設備壓力表（指針指在綠色沒有問題，黃色、紅色危險）。
3. Always pay attention to the pressure gauge of hydraulic equipment (the pointer indicates that there is no problem in green, and yellow and red are dangerous).
4.注意膠筒壓力表（A組份膠6bar,B組份膠4bar）。
4. Pay attention to the rubber cylinder pressure gauge (6bar for component A and 4bar for component B).
工作完畢后，關閉設備，打開膠槍，將膠槍內的膠全部擠出壓力小于30bar，如長時間不用，先將Operatingmade(操作模式開關)打至BASEPURGE(基料沖洗)，再打開膠槍，直至A組份膠全部擠出，設備關閉，繼續打膠直至壓力小于30bar后放入冷凍箱。
After the work is completed, turn off the equipment, turn on the glue gun, and extrude all the glue in the glue gun with the pressure less than 30bar. If it is not used for a long time, first turn the operatingmode switch to BasePage (base material flushing), and then turn on the glue gun until all the glue of component A is extruded, turn off the equipment, continue to glue until the pressure is less than 30bar, and then put it into the freezer.
以上就是今天帶給大家的知識，全自動封膠機專注行業多年，為用戶不斷的提供有價值的內容，更多內容請繼續關注我們：http://linshi.jncsjx.com
The above is the knowledge brought to you today. The automatic sealing machine has focused on the industry for many years and continuously provides users with valuable content. Please continue to pay attention to us for more content: http://linshi.jncsjx.com
- 中空玻璃加工設備：精準控工防起霧，筑牢中空玻璃密封與品質防線 2026/03/06
- 中空玻璃生產線實操科普：昌盛測厚段，用精準測量護航高效 2026/03/05
- 中空玻璃生產線實操科普：掃描儀這樣調整，尺寸識別更精準 2026/03/04
- 全自動封膠線實操科普：合片玻璃錯位？兩步排查輕松解決 2026/02/25
- 中空玻璃加工設備：針閥漏膠？這樣更換密封，簡單又牢固 2026/02/23
- 雙組份打膠機報警？循環泵超時這樣處理，快速恢復生產 2026/02/21
- 中空玻璃打膠機，助您開啟高效生產新時代！ 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡？這樣調，傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題：壓力夠卻打不滿膠？這樣排查就解決 2026/02/12
- 全自動封膠線實操科普：山東昌盛板壓段，筑牢封膠質量核心防線 2026/02/10
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
