打膠機是專門對膠粘劑等涂料進行控制并點滴、涂覆于產品表面的自動化設備。它是通過壓縮空氣將涂料送進供膠管，然后通過程序控制，將涂料按照預先設定的路徑進行點滴或者涂覆，
Gluing machine is an automatic equipment that controls and drips the adhesive and other coatings on the surface of products. It sends the paint into the rubber supply pipe through compressed air, and then drips or coats the paint according to the preset path through program control,
現如今中空玻璃設備市場愈演愈烈，各個廠家出的中空玻璃機器也是五花八門，然而中空設備的壽命往往在銷售到客戶手里以后，得不到很好的保障，有的客戶違規操作和不按規定實際操作機器設備，從而導致中空玻璃打膠機的壽命大大折扣，打膠機中空設備后期的維修和保養也是至關重要的，今天我在這里介紹一下如何使打膠機中空設備利用率提高到更大：
At present, the market of insulating glass equipment is becoming increasingly fierce, and the insulating glass machines produced by various manufacturers are also diverse. However, the service life of insulating glass equipment is often not well guaranteed after it is sold to customers. Some customers operate the machines and equipment in violation of regulations and do not operate them according to regulations, which leads to a significant discount in the service life of insulating glass sealer. The later maintenance and repair of the insulating glass equipment of the sealer is also crucial, Today, I would like to introduce how to improve the utilization rate of the hollow equipment of the glue machine:
一、使中空設備壽命如何加長，比如現在加工中空設備廠里常見的中空玻璃生產線，中空玻璃生產線主要組分部分就是立式的玻璃清洗干燥機和自動板壓裝置，清洗段基本都是采用全部不銹鋼材質的，一般不會輕易生銹。
1、 How to prolong the service life of the hollow equipment? For example, the common hollow glass production line in the processing hollow equipment factory now. The main components of the hollow glass production line are the vertical glass cleaning and drying machine and the automatic plate pressing device. The cleaning section is basically made of all stainless steel materials, which will not rust easily.
二、保養的部分在清洗室里面，毛刷及海綿管和轉動軸承的保養，由于清洗室里面下端經常被水打濕，要特別注意下端軸承的使用情況，海綿管在使用中一定要完全浸濕以后在進行工作，不然非常容易造成玻璃和海綿管的損壞。
2、 The maintenance part is in the cleaning room. The brush, sponge tube and rotating bearing are maintained. Since the lower end of the cleaning room is often wetted by water, special attention should be paid to the use of the lower end bearing. The sponge tube must be completely wetted before working, otherwise it is very likely to cause damage to the glass and sponge tube.

三、再者就是生產線后面的全自動板壓段，一般板壓段里面都是電磁閥和氣缸安裝的地方，要注意定期維護及保養，保證潤滑效果。
3、 In addition, there is a fully automatic plate pressing section behind the production line. Generally, the plate pressing section is where the solenoid valve and cylinder are installed. Pay attention to regular maintenance and service to ensure the lubrication effect.
四、比如中空玻璃生產過程中，中空玻璃內部結霧。產生原因：由于二道密封劑質量不穩定或質量不過關，在陽光的照射下?lián)]發到中空玻璃內部導致結霧；或者是干燥劑質量差，在太陽光照射下，釋放低分子物，導致結霧。
4、 For example, in the production process of insulating glass, fog forms inside the insulating glass. Cause: due to the unstable or unqualified quality of the secondary sealant, it volatilizes to the interior of the insulating glass under the sunlight, resulting in fogging; Or the quality of the desiccant is poor, and it releases low molecular substances under the sunlight, resulting in fogging.
五、中空玻璃生產過程當中一定要注意細節，包括中空玻璃設備的使用維修及中空玻璃的材料選用都很關鍵。
5、 Attention must be paid to details during the production of insulating glass, including the use and maintenance of insulating glass equipment and the selection of insulating glass materials.
六、丁基膠涂膠機是中空玻璃設備中的要用的設備，主要的功能是給鋁框涂丁基膠的，也是使用比較頻繁的設備。當遇到丁基膠涂布機擠出的丁基膠，出現毛刺不光滑時的解決方法，如果是新設備，應先觀察出膠孔是否光滑，如果出膠孔粗糙，應先打磨，再試機器；舊機器，由于設備的溫度傳感器有時不靈敏，顯示的溫度與實際的不相符，這時就需要將溫度進行上調，直到出膠正常為止，當遇到丁基膠不沾鋁條和玻璃時，是由于溫度的影響造成，建議將溫度進行上調到合適為止。
6、 Butyl adhesive coating machine is the equipment to be used in insulating glass equipment. Its main function is to apply butyl adhesive to aluminum frame, and it is also the equipment used frequently. When the butyl rubber extruded by the butyl rubber coater is not smooth, the solution is to observe whether the glue hole is smooth if it is new equipment. If the glue hole is rough, polish it first, and then try the machine again; For the old machine, because the temperature sensor of the equipment is sometimes not sensitive and the displayed temperature is not consistent with the actual temperature, it is necessary to raise the temperature until the glue is normal. When the butyl rubber is not stained with aluminum strips and glass, it is due to the influence of temperature. It is recommended to raise the temperature until it is appropriate.
中空玻璃設備日常保養與維護策略，是需要時時刻刻注意的事情，一旦發現中空玻璃設備有異常，應立即進行檢修，保證中空玻璃進行能夠良好運行，保障中空玻璃生產效率。
The daily maintenance and maintenance strategy of insulating glass equipment is something that needs to be paid attention to at all times. Once the insulating glass equipment is found abnormal, it should be repaired immediately to ensure that the insulating glass can operate well and ensure the production efficiency of insulating glass.
以上就是為大家介紹的有關中空玻璃加工設備詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://yfcha.com
The above is the detailed introduction of the insulating glass processing equipment introduced for you. I hope it can help you. If you have any questions, please contact us. We will provide you with our service with our attitude http://yfcha.com