雙組份打膠機在咱們平常的使用過程中有許多需求留意的事項，假如咱們平常不留神留意這些地方很可能會形成咱們的雙組份打膠機呈現各式各樣的毛病。這樣不光影響你的出產功率降低你的收益還會大幅度的降低設備的壽命
There are many things we need to pay attention to in our normal use of the two-component dispenser. If we don't pay attention to these places, it is likely that our two-component dispenser will present various problems. This will not only affect your production power, reduce your revenue, but also significantly reduce the life of the equipment
今天小編就介紹下關于雙組份打膠機在平常出產操作中究竟應該留意哪些方面。各位可以依照小編所寫的內容嚴格執行操作，以免呈現各種不必要的問題以及毛病。
Today's small edition on the introduction of two-component sizing machine in the ordinary production operation should pay attention to which aspects. You can strictly follow the contents of the editor to avoid unnecessary problems and problems.
一、需要注意的事項
1、 Precautions
1、壓盤上的放氣閥門要保持曉暢，要定時疏通和清洗。
1. The air release valve on the pressure plate shall be kept clear, dredged and cleaned regularly.
2、正常作業時不要斷氣源，假如發現斷氣源應中止作業。
2. Do not cut off the air source during normal operation. If any, stop the operation.
3、若雙組份打膠機涂膠作業過程中停頓時刻超過15分鐘以上時，必定要用“沖槍”。本機有報警功能，屆時沒有沖膠會有蜂鳴器報警。
3. If the pause time is more than 15 minutes in the process of two-component gluing machine gluing operation, it is necessary to use "shot gun". This machine has an alarm function. There will be a buzzer alarm if there is no glue flushing.
4、定時查看氣源，應確保使用經干燥的潔凈壓縮空氣，并定時排放別離過濾器中的積水，查看油霧器中的油是否夠用。
4. Check the air source regularly. First, make sure to use dry and clean compressed air, regularly discharge the accumulated water in the separate filter, and check whether the oil in the oil atomizer is sufficient.
5、硅酮膠B 組份遇空氣會結殼，影響泵的正常作業和管路的疏通，因而，停機時B組份膠的一切通道在泄壓后均應關閉，使B組份不得接觸空氣。
5. In case of air, component B of silicone rubber will crust, which will affect the normal operation of the pump and the dredging of the pipeline. Therefore, all channels of component B rubber shall be closed after pressure relief during shutdown, so that component B shall not contact the air.

6、B膠桶內假如要有空氣，空氣將排不出來，B泵將快速往復運動，不能向高壓泵內正常供膠，影響整個系統，因而，必須將空氣排出來。辦法是：將壓盤提出重新壓入并放氣。
6. If there is air in the B rubber barrel, the air will not be discharged, and the B pump will move rapidly to and fro, and cannot supply glue to the high pressure pump normally, which will affect the whole system. Therefore, the air must be discharged. The method is: lift the pressure plate and press it in again and release the air.
7、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿意膠嘴正常出膠均勻打膠即可。翻開液壓站時必定要翻開膠槍，否則B組份管路壓力將升得很高，形成安全事故。
7. The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as the indoor environment temperature, adjust the pressure to the satisfaction that the glue nozzle is normal and the glue is evenly applied. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, forming a safety accident.
8、A膠提膠泵接連作業1分鐘以上沒有供膠中止，說明管路內有空氣，此刻會報警，須翻開泵上管接頭再翻開A膠提膠泵，直到出膠中止，中止并接好接頭，膠槍會呈現有空氣的嗶嗶爆炸聲，空氣排凈就好了。
8. The continuous operation of a glue lift pump for more than 1 minute does not stop the supply of glue, which means there is air in the pipeline. At this moment, an alarm will be given. It is necessary to open the upper pipe joint of the pump and then the a glue lift pump until the delivery of glue is stopped. Stop and connect the joint. The glue gun will show an air beep explosion, and the air will be discharged completely.
9、因為每次沖洗混合器不會完全潔凈，每次都有少量的混合膠堆積，越來越多，致使堵塞混合器通道，用一段時刻后，影響出膠量和混合效果，因而要定時(聚硫膠五天，硅酮膠兩天)清洗混合器。把混合器內的混膠棒拆出，如有損壞替換新的混膠棒。若混膠棒拆不出來，可用火燒掉，留意不能損傷零件螺紋。
9. Because the mixer will not be completely clean every time, a small amount of mixed rubber will accumulate every time, more and more, which will block the mixer channel. After a period of time, the rubber output and mixing effect will be affected, so it is necessary to clean the mixer regularly (polysulfide rubber for five days, silicone rubber for two days). Remove the mixing bar in the mixer, and replace it with a new one if it is damaged. If the rubber mixing rod cannot be removed, it can be burnt out by fire. Pay attention not to damage the thread of parts.
二、雙組份打膠機設備保養
2、 Maintenance of two-component gluing machine
雙組份打膠機的清潔噴槍表面、清理噴嘴，確保噴嘴的疏通;
Clean the surface of the spray gun and the nozzle of the two-component gluing machine to ensure that the nozzle is unblocked;
清潔或替換膠機和噴槍的過濾網;
Clean or replace the filter screen of glue machine and spray gun;
查看噴槍是否有漏膠現象，如有漏膠現象請調理，維修、替換噴槍、噴頭、噴嘴等需求替換的部件。
Check whether the spray gun has leakage. If there is leakage, please adjust, repair and replace the spray gun, nozzle, nozzle and other parts that need to be replaced.
查看膠缸內壁是否有炭化層，如有炭化層請使用諾信專用清洗液R溶劑清洗膠缸。
Check whether there is a carbonized layer on the inner wall of the rubber cylinder. If there is a carbonized layer, please clean the rubber cylinder with the special cleaning solution r of nuoxin.
將膠機加熱至操作溫度，排空膠箱內的熱溶膠。查看膠缸內是否有雜質，如有雜質用潔凈的抹布清潔膠缸。
Heat the glue machine to the operating temperature and empty the hot-melt glue in the glue box. Check whether there are impurities in the rubber cylinder. If there are impurities, clean the rubber cylinder with a clean cloth.
查看雙組份打膠機的一切接線盒和接線柱是否結實;
Check whether all junction boxes and terminals of the two-component dispenser are firm;
查看一切電源銜接線是否有破損現象，其他絕緣件是否牢靠;
Check whether all power plug wires are damaged and other insulation parts are secure;
清潔及查看膠機電器箱內部;
Clean and check the inside of the rubber machine electrical box;
查看雙組份打膠機的一切電源銜接線銜接是否牢靠。
Check whether all power pins of the two-component dispenser are firmly connected.