中空玻璃打膠機撤出空桶，將新膠桶置于工作位置，重復第3、4、項操作。
The hollow glass glue machine withdraws the empty bucket, puts the new glue barrel in the working position, repeats the third, fourth and the operation.
1、膠槍：因雙組份膠是由兩種膠混合而成的，其凝固速度與環境溫度和A、B膠的比例有關，混合后的膠一般在20分鐘之內就會反應固化。所以，當設備在正常打膠后，20分鐘之內不使用就必須將混合后的膠沖洗出來，以免堵塞混膠器和膠槍。
1, glue gun: because the two component glue is made of two kinds of glue, its solidification speed is related to the ambient temperature and the proportion of A and B glue. After mixing, the glue will react and solidify in 20 minutes. Therefore, when the equipment is not used in 20 minutes after normal glue, the mixed glue must be flushed out in order to avoid blocking the mixer and glue gun.
1)松開比例杠桿上的比例泵鎖緊螺釘，將比例泵內外調整至所需比例。只有當A膠和B膠的配比達到正常值時，才可進行下面的操作。

1) unlock the proportion pump locking screw on the proportional lever, and adjust the ratio pump to the required proportion. Only when the ratio of A glue and B glue reaches the normal value, the following operation can be carried out.
2)置選擇旋鈕于A、B泵開，將膠槍出口對準兩片玻璃的中縫，打開膠槍開關，以適當速度平穩地移動膠槍使玻璃槽內的雙組份膠填滿充實為佳。打膠結束時關閉膠槍。
2) set the option knob on A and B pump, open the rubber gun outlet to the two piece of glass seam, open the glue gun switch, and move the glue gun smoothly at a suitable speed, so that the two component glue in the glass tank can be filled and enriched. Turn off the glue gun at the end of the glue.
3）打開 中空玻璃打膠機A（或B）膠泵充氣開關，選擇A（或B）膠泵提升機構為上升位置，點動旋鈕使壓盤慢慢提起，此時應注意：膠桶盡量不要離開底盤，直至壓盤完全脫離膠桶時關閉A（或B）膠泵的充氣開關。
3) open the hollow glass glue machine (A or B) inflatable rubber pump switch, select A (or B) rubber pump lifting mechanism for upward position, move the knob plate slowly lift, you should pay attention to: plastic barrel so as not to leave the chassis, turn off A until the platen completely out of plastic barrel when (or B) the inflatable rubber pump switch.
4）中空玻璃打膠機具體操作：將B泵關閉，打開B膠回流開關然后打開膠槍，至膠條為白色即可。
4) the concrete operation of the hollow glass rubber machine: the B pump is closed, the B glue reflux switch is opened and the glue gun is opened to the white glue bar.
5）把中空玻璃打膠機混合器放到水火燒，直到把混合芯拿出為至；注黑把手里面還有一結。混合器和槍頭之間的旋轉部位不可燒；槍頭不可燒?？捎描F絲打通為止
5) put the mixer of the hollow glass glue machine into the water and fire until the mixed core is taken out, and there is a knot in the black handle. The rotating parts between the mixer and the gun head are not burned, and the head of the gun can not be burned. The wire can be made through the wire
本文由雙組份打膠機友情奉獻.更多有關的知識請點擊:http://yfcha.com我們將用的技術.真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待
This article is a friendship contribution from two component glue machine. Please click on more related knowledge: http://yfcha.com, we will use the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will dedicate more knowledge to you. Please look forward to it.