當前位置：打膠機工作過程中膠體出現結皮或硫化現象的原因
時間：2022-10-26 來源：http://yfcha.com/ 發布人：昌盛機械
當雙組份膠在混合過程中發生局部固化時，打膠機打出來的膠就會出現結皮或硫化現象。出現這一現象的原因主要有三種：
When the two-component rubber is partially solidified in the mixing process, the rubber produced by the rubber beater will be skinned or vulcanized. There are three main reasons for this phenomenon:
⑴膠體顏色較黑，固化快時，可能是由于B組分比例過高，過多的催化劑促使固化速度加快。此時，需要適當降低B組分的比例，將結皮或硫化膠沖洗干凈后施工；
⑴ The colloid color is dark, and the curing speed is fast, which may be due to the high proportion of component B, and excessive catalyst to accelerate the curing speed. At this time, it is necessary to reduce the proportion of component B appropriately, and wash the crust or vulcanizate before construction;
⑵打膠機若打膠過程中伴有出膠慢的現象時，可能是混合芯長時間未清洗或清洗不徹底，膠體結皮堵塞管道。因此，定期清洗靜態混合器是很有必要的。
(2) If the glue dispensing process of the glue dispenser is accompanied by slow glue dispensing, it may be that the mixing core has not been cleaned for a long time or is not thoroughly cleaned, and the glue crust blocks the pipeline. Therefore, it is necessary to clean the static mixer regularly.
⑶當固化和出膠速度均無異常，而打出的膠仍有結皮或硫化現象時，則可能是設備停機時間較長，膠槍未清洗或洗槍不夠徹底，需要將結皮或硫化膠沖洗干凈后后施工。
(3) When the curing and rubber discharging speed are normal, but the rubber still has skinning or vulcanization, it may be that the equipment has been shut down for a long time, the rubber gun has not been cleaned or the cleaning gun is not thorough enough, and it is necessary to clean the skinning or vulcanization rubber before construction.
以上就是為大家介紹的有關雙組份打膠機詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://linshi.jncsjx.com
The above is a detailed introduction to the two-component sealant dispenser, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our service in our attitude http://linshi.jncsjx.com
- 玻璃涂布機設備解析：技術分類洞察 2025/06/09
- 全自動鋁條折彎機長期使用中典型出現的問題是什么，怎么解決？ 2025/06/07
- 中空玻璃加工設備：立式與臥式清洗機的差異化解析 2025/06/06
- 雙組份打膠機切換膠水清潔全流程解析 2025/06/05
- 全自動封膠線輔助傳送前限位是什么意思？ 2025/06/04
- 雙組份打膠機是為解決什么問題產生的呢？ 2025/06/03
- 全自動丁基膠涂布機操作注意事項：細節決定品質與效率 2025/05/27
- 雙組份打膠機：解碼膠水混合后的固化時間控制藝術 2025/05/26
- 臥式丁基膠涂布機傳動系統維護要點解析 2025/05/20
- 中空玻璃加工必備8大設備詳解 2025/05/19
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
