當前位置：避免玻璃脫離定位的十大核心原理
時間：2017-11-02 來源：http://yfcha.com/ 發布人：昌盛機械
1、混膠或沖槍(沖洗混膠器、膠嘴)時，雙組份打膠機必須把機頭行走到軌道末端，用接膠板接住膠嘴內放出的膠，以免污染設備。
1, mixing glue or gun (Flushing glue mixer, glue mouth), must move the nose to the end of the track, with the rubber plate to catch the glue released from the glue mouth, so as not to pollute the equipment.
2、操作參數設置時，在控制箱pc顯示屏上進行，根據須要而選擇設定值，不要隨意設定，以免控制器發出錯誤的信息，影響打膠質量或損壞設備。
2, the operation parameters are set, in the control box PC display screen, according to the need to choose the set value, do not arbitrarily set, so as to avoid the controller send out wrong information, affect the quality of glue or damage equipment.
3、混膠或沖槍時，一定要先打開膠嘴控制閥門，然后再打開供膠機，以免壓力劇增損壞設備或者出現安全事故。
3, mixing glue or gun, must first open the glue mouth to control the valve, and then open the glue machine, so as to avoid the pressure surge, damage equipment or safety accidents.
4、打膠時一定要扶好玻璃，避免玻璃脫離定位，影響打膠質量。
Must hold the glass 4, glue, glass to avoid the influence from positioning, glue quality.
5、沖槍時先關閉機頭上的B膠出膠閥門，關閉B膠泵，然后打開B膠回流閥門，后沖槍，沖洗至出膠口不出黑膠，沖洗才能結束。
5, when the gun, first off the head of B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally gun, rinse to the glue mouth without black glue, rinse can finish.
6.機頭電機下面不要有異物，遠離電機以免發生危險。
The 6. head motor below do not have a foreign body from the motor to avoid danger.
7.機頭前方檢測玻璃開關的光眼上不能有膠，否則誤工作。
7. light eye detection of glass on the front of the head of the switch can not have glue, or work.
8.膠嘴和兩側的刮膠板如膠多時要清理。
8. glue scraping plate on both sides of the mouth and a long time to clean up such as glue.
9.吸盤上不能放石灰粉，如有膠請清理，如果有的玻璃邊緣正好放到吸盤的中心時，可調節吸盤左右移動.
9. on the sucker can not put lime powder, if there is glue, please clean, if some glass edge just put into the center of the sucker, can adjust the sucker moving around
10.打三玻時要將鋁框檢測探針缷掉，雙玻時在安裝上。
10. hit three glass to the aluminum frame detection probe off off, when the installation of double glass.
安裝探針：將探針上的彈簧壓到小時探針的前端與膠嘴平齊時固定好。
Install the probe: press the spring on the probe to the tip of the probe, and fix it when the nozzle is flush.
本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://yfcha.com謝謝您的到來!
The wonderful content of this article comes from the two component dispenser, please click on our official website: http://yfcha.com, thank you for coming!
- 全自動封膠線有什么技術優勢？ 2025/04/18
- 中空玻璃生產線成本高，怎么選性價比高的？ 2025/04/15
- 驗收時才發現玻璃自爆，工期延誤賠償百萬？ 2025/04/14
- 中空玻璃加工設備的講解 2025/04/12
- 毛刷式清洗機怎么使用 2025/04/11
- 中空玻璃加工設備核心是什么？ 2025/04/10
- 全自動鋁條折彎機如何設置更快，讓編程更簡單？ 2025/04/09
- 雙組份打膠機讓膠水發揮最大威力 2025/04/08
- 臥式丁基膠涂布機的優勢有什么 2025/04/07
- 封膠線麻煩？全自動封膠線了解一下 2025/04/01
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
